Skip to main content

Explainer · 3 min 17 s

Incoloy 800, 800H, 800HT: read the designation

Incoloy 800, 800H and 800HT are one alloy read against four lines on the specification: carbon, the combined Al + Ti, the minimum anneal and the ASTM grain r…

Format
Explainer
Published
Duration
3 min 17 sec
Language
English
Full explainer series: Junda Explainers

About this video

This explainer is educational. It explains the published limits and the order fields for the topic; confirm the grade, standard, size, condition, inspection and documents with Junda for each order.

Chapters

Each chapter opens the video at that point on YouTube.

  1. 0:00

    Incoloy 800, 800H, 800HT: read the designation

    Incoloy 800, 800H and 800HT are three names for one alloy family. Four lines on the specification separate them, and only three of those lines can be poured.

  2. 0:12

    What Incoloy 800, 800H and 800HT mean: UNS N08800, N08810, N08811

    800 is N08800, capped at zero point one zero carbon. 800H is N08810, 800HT is N08811, one window inside the other.

  3. 0:29

    One alloy: nickel 30 to 35, chromium 19 to 23, aluminium and titanium

    All three are a nickel-iron-chromium alloy at heart. Nickel runs thirty to thirty-five percent, and chromium nineteen to twenty-three. Aluminium and titanium sit in every analysis, each one between zero point one five and zero point six zero. Roll three tubes from three heats and you cannot tell them apart. The base analysis, the surface and the size are the same. Nothing you can see says which designation the mill is allowed to put on the pipe.

  4. 0:59

    The Al + Ti sum and the 1150 °C solution anneal that sets the grain rating

    The rule that gets missed is a sum. 800HT needs the sum between zero point eight five and one point two zero. Two pass, the sum fails: zero point three plus zero point three is zero point six. A passing sum reads zero point four five plus zero point four five. Chemistry is poured. The grain rating is made. A mill anneal leaves 800 fine grained. 800H and 800HT are solution annealed at a minimum of one thousand one hundred and fifty degrees. That heat coarsens the grain to ASTM number five or coarser. ASTM E112 rates the grain on a polished section of the wall. Five or coarser is what 800H and 800HT have to show. A fine-grain pipe cannot be certified as either, whatever its carbon and aluminium say. Above five hundred and forty degrees the wall carries its load for long periods. Under that load it creeps: it stretches slowly and permanently. The coarse grain is what slows that, and the grain rating is where the mill records it. So the order specifies the anneal with the grade, not the grade alone. In service, the difference is time at temperature. Above six hundred degrees the coarse grain carries up to double the creep strength. That is what 800H and 800HT are specified for.

  5. 2:22

    How to specify Incoloy 800H or 800HT pipe: UNS, standard, condition, grain

    A catalogue name proves nothing: 800T is not a UNS designation at all. Carbon and the sum can both sit in the window on a pipe that was never solution annealed. The proof is the certificate: the anneal and the grain rating on one sheet. One more name sits on the catalogue: Incoloy 800T. 800T is not a UNS designation, and nothing on the pipe says which one it is. So the enquiry asks for the UNS number and the supply condition. The order records the designation the answer names. Write the UNS number and the standard: B407 for pipe, B163 for tubing. Add the anneal minimum, the grain rating, and an EN 10204 type 3.1 certificate. Send the designation, the size and the service temperature, and we confirm the pipe and its documents against them.

Specify the pipe or tube for your project

Send the grade, standard, OD × wall × length, wall basis, quantity, inspection and documents with your enquiry.