Skip to main content

Explainer · 3 min 10 s

Inconel 625 ASTM B444 Grade 1 vs Grade 2

ASTM B444 supplies Inconel 625 pipe in two heat-treatment conditions, Grade 1 and Grade 2, and the design temperature decides which one the order has to name…

Format
Explainer
Published
Duration
3 min 10 sec
Language
English
Full explainer series: Junda Explainers

About this video

This explainer is educational. It explains the published limits and the order fields for the topic; confirm the grade, standard, size, condition, inspection and documents with Junda for each order.

Chapters

Each chapter opens the video at that point on YouTube.

  1. 0:00

    Inconel 625 ASTM B444 Grade 1 vs Grade 2

    Inconel 625 seamless pipe comes in two conditions under ASTM B444. Grade 1 annealed, Grade 2 solution annealed: the certificate decides.

  2. 0:13

    What ASTM B444 Grade 1 and Grade 2 mean for Inconel 625 pipe

    Every 625 line names the standard, the UNS number and the grade. The grade is a heat treatment: annealed at a minimum of eight hundred and seventy-one degrees, or solution annealed at one thousand and ninety-three. Choose one, or the mill chooses for you.

  3. 0:31

    Inconel 625 chemistry: nickel 58, chromium 20 to 23, molybdenum 8 to 10

    Both grades are the same alloy, so the chemistry does not move. Nickel at fifty-eight percent minimum, chromium at twenty to twenty-three, molybdenum at eight to ten. Niobium plus tantalum at three point one five to four point one five strengthens it without an aging step, and carbon is capped at zero point one zero. The pipe starts as a pierced hollow. A die outside and a mandrel inside squeeze the wall as it is drawn, and no weld runs along it. Before the last pass it is annealed, and that anneal is where the two grades part. Seven published steps, with cold drawing and cold rolling in the middle. Then two solution heat treatment lines: the one station that depends on the grade. Grade 1 stops at eight hundred and seventy-one degrees. Grade 2 goes to one thousand and ninety-three. Everything after it is the same.

  4. 1:23

    Grade 1 annealed vs Grade 2 solution annealed: yield strength or creep strength

    Same line, same pressure, same size. Grade 1 carries a minimum yield of four hundred and fourteen megapascals; Grade 2 carries two hundred and seventy-six. Lower yield means more wall for the same pressure, and a heavier pipe. In a cold line, Grade 2 is not a free upgrade. Below five hundred and ninety-three degrees, the job is corrosion. Grade 1 is specified there: fine grain, higher yield, and a wall the exchanger can use. The tubes pass through a tube sheet, and every joint has to stay tight. Above five hundred and ninety-three degrees, the question changes. The wall still holds the pressure, but the metal begins to creep: slow stretching that ends in rupture. Grade 2 is the coarse-grain condition specified for that range.

  5. 2:11

    How to specify Inconel 625 ASTM B444 pipe on a purchase requisition

    So the design temperature decides the grade, before price or delivery does. Five hundred and ninety-three degrees for Grade 1, and nine hundred and eighty-two for Grade 2. The size is the other line that gets left open. NPS 2 is 60.3 millimetres outside diameter, Schedule 40S is 3.91 millimetres nominal wall, and the basis is nominal or minimum. Write all of it on the line item, so the mill cannot choose for you. Standard and grade with the anneal minimum, then size and wall basis to B36.19M. Then the tests: one hundred percent ultrasonic to ASTM E213, and hydrostatic to B444. And an EN 10204 type 3.1 certificate that carries the heat-treatment log. Send the grade, the size and the service temperature, and we confirm the pipe and its documents against them.

Specify the pipe or tube for your project

Send the grade, standard, OD × wall × length, wall basis, quantity, inspection and documents with your enquiry.