2 min 19 sPenerangan ·
PREN Calculator: Check a Supplier's Material Certificate
A PREN calculator result needs documented heat chemistry: replace typical presets, reconcile the formula and record any missing evidence.
YouTube · Penerangan
Video penerangan spesifikasi dan Shorts daripada saluran YouTube Junda. Setiap video dipautkan ke halaman produk yang diterangkannya.
2 min 19 sPenerangan ·
A PREN calculator result needs documented heat chemistry: replace typical presets, reconcile the formula and record any missing evidence.
3 min 9 sPenerangan ·
Eight fields turn a project datasheet into one stainless steel pipe line a mill can quote: standard and edition, wall basis, inspection scope and quantity.
53 sPenerangan ·
One word inside a pipe enquiry decides what arrives: the wall basis. Average wall or minimum wall on the same NPS 4 schedule 40S pipe.
29 sPenerangan ·
A 1/2 in tube is 12.70 mm outside and an NPS 1/2 pipe is 21.3 mm; schedule 40S leaves a 15.76 mm bore against 9.70 mm, so name the size and the wall basis.
2 min 17 sPenerangan ·
Seven published steps take a seamless pipe from a hollow to a tested length: forming, heat treatment, pickling, cutting, inspection.
3 min 5 sPenerangan ·
How the wall, the grade and the length set a seamless pipe's mass per metre, worked through at DN 150 in 316L and 2507, to a 6 m length and a U-bend.
3 min 31 sPenerangan ·
317L vs 316L: both seamless austenitic pipe to the same standards. The step is molybdenum, and one point of it is 3.3 PREN.
3 min 14 sPenerangan ·
An educational explainer on stainless steel tube sizes: the published ASME B36.19 chart, mass per metre, how the mill draws the wall, and the line that carries a size into an enquiry.
3 min 17 sPenerangan ·
Incoloy 800, 800H and 800HT are one alloy read against four lines on the specification: carbon, the combined Al + Ti, the minimum anneal and the ASTM grain r…
2 min 59 sPenerangan ·
Austenitic stainless steel pipe is one family, not one grade: seven grades leave the mill looking the same, and two different questions pick between them.
2 min 33 sPenerangan ·
316L welded service is where the letter L is most often misread: it covers the metal beside the weld, not the weld, its surface or the fluid.
2 min 54 sPenerangan ·
904L stainless steel pipe in acid service is one grade and four published conditions: the acid's character, its concentration, its temperature and the rest o…
3 min 13 sPenerangan ·
Super austenitic vs super duplex is not a corrosion score: 254SMO and 2507 reach almost the same pitting number, and the structure decides the rest.
2 min 37 sPenerangan ·
Hastelloy C-276 pipe corrosion data is a specimen in one bath at one concentration and one temperature: 0.1 mm a year is the line, and twenty years on that l…
3 min 10 sPenerangan ·
ASTM B444 supplies Inconel 625 pipe in two heat-treatment conditions, Grade 1 and Grade 2, and the design temperature decides which one the order has to name…
2 min 37 sPenerangan ·
A heat exchanger tube specification is three different documents: straight tube, U-bend tube and rectangular profile each need a different drawing, and the m…
2 min 15 sPenerangan ·
A mill test certificate only proves a pipe when the heat number, the grade and the tests on the paper match the marking on the steel.
3 min 14 sPenerangan ·
An educational explainer on the two duplex grades a buyer actually chooses between: published chemistry in the pitting resistance equivalent, strength minima side by side, the 600 to 1000 °C sigma window, the designations on the certificate and the enquiry line.
2 min 38 sPenerangan ·
UT, ET and hydrostatic testing answer three different questions: ultrasonic testing reads the wall volume, eddy current testing reads the surface and the lay…
2 min 41 sPenerangan ·
347 vs 347H stainless steel pipe: 347 allows up to 0.08 % carbon, 347H is held between 0.04 and 0.10 %, and that window is what changes the anneal, the grain…
2 min 58 sPenerangan ·
ASTM A312, A269 and A213 all cover 316L, but only one describes your line item: pressure piping, general-service tubing or an exchanger tube.
2 min 52 sPenerangan ·
An educational explainer on pickling and passivation of stainless steel pipe: what each treatment removes, matching the treatment to the surface condition, what a photo, ASTM A380 and ASTM A967 do and do not prove, and what to write into a pipe enquiry.
3 min 13 sPenerangan ·
An educational explainer on the pitting resistance equivalent number: the formula term by term, a worked example, PREN ranges from published 2507 and 254SMO chemistry, what PREN does not document, and how to write a PREN requirement into a pipe enquiry.
3 min 2 sPenerangan ·
An educational explainer on specifying S32750 super duplex tubing: ASTM A789 for tube, A790 for pipe, wall basis, inspection and document requirements.
3 min 23 sPenerangan ·
An educational explainer on specifying stainless steel pipe or tube: product form, dimensions, cold drawing, tube geometry, inspection and quotation documents.
46 sShort ·
A PREN calculator result starts with the offered heat's certificate. Missing nitrogen? Request the documented chemistry before continuing the review.
48 sShort ·
The seamless tube route starts from a hollow, not a sheet: cold forming, heat treatment, pickling, straightening, cutting and inspection.
47 sShort ·
DN 150 in 316L is 14.09 kg/m in schedule 10S and 28.80 in 40S, so a 6 metre length is 84.55 kg and a hundred of them are 8,455 kg.
22 sShort ·
One size, three masses: DN 150 in 316L is 14.09 kg/m in schedule 10S and 28.80 in 40S, and 13.74 kg/m in grade 2507, all theoretical from the published formula.
51 sShort ·
317L vs 316L: same mill, same size, same standards. One carries more molybdenum, and one point of molybdenum is 3.3 PREN.
17 sShort ·
The short version of the size explainer: NPS is a trade size, the millimetres are the size, and the wall basis is written with it.
58 sShort ·
Incoloy 800, 800H and 800HT are one alloy, and the name is not in the metal: carbon, the combined Al + Ti and the 1150 °C anneal with its grain rating decide…
50 sShort ·
Austenitic stainless steel pipe is one family: seven grades leave the mill looking identical, and they are bought on two different axes.
50 sShort ·
The L in 316L covers the band beside the weld — carbon 0.030 % maximum, chromium stays in the metal. It does not cover the bore surface, the procedure or…
45 sShort ·
One 904L page: 0–98 % sulphuric acid, and only 1–2 % hydrochloric acid. The acid decides which of the four conditions you are ordering.
51 sShort ·
254SMO and 2507 land on the same pitting number. The structure is what decides: one phase or two, 300 or 550 MPa, and what the mill has to prove.
55 sShort ·
A C-276 corrosion rate is measured on a specimen in one bath at one concentration and one temperature: 0.1 mm a year is the line, and twenty years on it is t…
48 sShort ·
One alloy, two heat treatments: ASTM B444 Inconel 625 pipe is supplied annealed at a minimum of 871 °C or solution annealed at a minimum of 1093 °C, and the…
54 sShort ·
A U-tube drawing has to fix four numbers: outside diameter and wall, bend radius, centre distance and leg length. Change the radius and the centre distance…
47 sShort ·
A mill test certificate is only proof when the heat number on the paper matches the marking on the pipe and the label on the bundle.
58 sShort ·
The short version of the 2205-versus-2507 explainer: one drawing route on a different alloy, and why the stronger grade is not the default choice.
53 sShort ·
A pipe can pass one inspection and still fail the next. UT, ET and hydrostatic testing each answer a different question: the wall volume, the surface, and…
53 sShort ·
347 allows up to 0.08 % carbon. 347H is held between 0.04 and 0.10 %, and the niobium has to follow. Same outside diameter, different condition, different…
52 sShort ·
One 316L grade, three ASTM documents, three test schedules. The same pipe end is written three ways: NPS and schedule, outside diameter and wall, the…
57 sShort ·
The short version of the pickling-versus-passivation explainer: two treatments, two targets, and an order line that still needs coverage, acceptance and responsibility.
53 sShort ·
The short version of the PREN explainer: the formula in three terms, one worked example, and what one nitrogen change does to the number.
56 sShort ·
S32750 is a grade, not a complete tube order. ASTM A789 for tube, A790 for pipe; state the wall basis and the inspection line.
43 sShort ·
Stainless steel pipe and tube can look identical, but the specification language differs. State the form, standard, grade, OD, wall and drawing.
Video diterbitkan dalam bahasa asalnya, dengan transkrip di setiap halaman tontonan. Piawaian, dimensi, keadaan bekalan, dokumen pemeriksaan dan terma komersial khusus projek mesti disahkan dengan Junda bagi setiap pertanyaan.
Hantar gred, dimensi, kuantiti dan dokumen yang diperlukan bersama pertanyaan Anda.